JN0-360 est un test de Juniper Certification, donc réussir JN0-360 est le premier pas à mettre le pied sur la Certifiction Juniper. Ça peut expliquer certiainement pourquoi le test Juniper JN0-360 devient de plus en plus chaud, et il y a de plus en plus de gens qui veulent participer le test JN0-360. Au contraire, il n'y a que pas beaucoup de gens qui pourrait réussir ce test. Dans ce cas, si vous vous réfléchissez étudier avec une bonne Q&A?
C'est sûr que le Certificat Juniper JN0-360 puisse améliorer le lendemain de votre carrière. Parce que si vous pouvez passer le test Juniper JN0-360, c'est une meilleure preuve de vos connaissances professionnelles et de votre bonne capacité à être qualifié d'un bon boulot. Le Certificat Juniper JN0-360 peut bien tester la professionnalité de IT.
Choisir le Pass4Test vous permet non seulement à réussir le test Juniper JN0-360, mais encore à enjouir le service en ligne 24h et la mise à jour gratuite pendant un an. Nous allons lancer au premier temps la Q&A Juniper JN0-360 plus nouvelle. Si vous ne passez pas le test, votre argent sera tout rendu.
On doit faire un bon choix pour passer le test Juniper JN0-360. C'est une bonne affaire à choisir la Q&A de Pass4Test comme le guide d'étude, parce que vous allez obtenir la Certification Juniper JN0-360 en dépensant d'un petit invertissement. D'ailleur, la mise à jour gratuite pendant un an est aussi gratuite pour vous. C'est vraiment un bon choix.
Vous pouvez comparer un peu les Q&As dans les autres sites web que lesquelles de Pass4Test, c'est pas difficile à trouver que la Q&A Juniper JN0-360 est plus complète. Vous pouvez télécharger le démo gratuit à prendre un essai de la qualité de Pass4Test. La raison de la grande couverture des questions et la haute qualité des réponses vient de l'expérience riche et la connaissances professionnelles des experts de Pass4Test. La nouvelle Q&A de Juniper JN0-360 lancée par l'équipe de Pass4Test sont bien populaire par les candidats.
Le test Juniper JN0-360 est le premier pas pour promouvoir dans l'Industrie IT, mais aussi la seule rue ramenée au pic de succès. Le test Juniper JN0-360 joue un rôle très important dans cette industrie. Et aussi, Pass4Test est un chaînon inevitable pour réussir le test sans aucune doute.
Dans cette Industrie IT intense, le succès de test Juniper JN0-360 peut augmenter le salaire. Les gens d'obtenir le Certificat Juniper JN0-360 peuvent gagner beaucoup plus que les gens sans Certificat Juniper JN0-360. Le problème est comment on peut réussir le test plus facile?
Code d'Examen: JN0-360
Nom d'Examen: Juniper (Juniper Networks Certified Internet Specialist (JNCIS-SP))
Questions et réponses: 252 Q&As
JN0-360 Démo gratuit à télécharger: http://www.pass4test.fr/JN0-360.html
NO.1 What is the function of the hop limit field in the IPv6 header?
A.It limits the diameter of the network to 20 hops
B.It sets the number of hops in the network to be equal to the MPLS header time-to-live (TTL)
C.It replaces the time-to-live (TTL) field in IPv4
D.It represents future extensibility to the protocol
Answer: C
Juniper certification JN0-360 certification JN0-360 JN0-360
NO.2 You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further
reduce down time if a Routing Engine (RE) failure occurs.
Which two features can be configured on this device to reduce its downtime in this situation? (Choose
two)
A.VRRP
B.GR
C.BFD
D.NSR
Answer: B D
Juniper examen certification JN0-360 JN0-360 JN0-360 JN0-360
NO.3 Which BGP state denotes a fully operational session?
A.Established
B.Active
C.Operational
D.Connect
Answer: A
Juniper JN0-360 JN0-360 JN0-360
NO.4 You have been asked to define a default gateway for traffic leaving a router. This route should use
interface so-0/0/0 as its next-hop.Which type of route would be suited for this scenario?
A.a static route
B.a generated route
C.a martian route
D.an aggregate route
Answer: A
certification Juniper JN0-360 JN0-360
NO.5 What are two valid actions that can be applied to a frame by a Layer 2 firewall filter?
(Choose two)
A.Log
B.loss-priority
C.sample
D.count
Answer: BD
Juniper certification JN0-360 JN0-360 examen JN0-360 JN0-360 examen
NO.6 Which IS-IS packet is used to determine the level of an IS-IS neighbor?
A.IIH
B.LSP
C.PSNP
D.CSNP
Answer: A
Juniper JN0-360 JN0-360 examen certification JN0-360 certification JN0-360
NO.7 You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy. You
have been asked to create a static route that will use 43 18 7 1 as its primary next-hop and 76 1310 2 as
its secondary next-hop.
Which command correctly configures this setup?
A.set static route 0/0 76.13.10.2 qualified-next-hop 43.18.7.1 pref 10
B.set static route 0/0 next-hop 43.18.7.1 secondary-next-hop 76.13.10.2 preference 10
C.set static route 0/0 next-hop [76.13.10.2 10.10.10.5] pref 10
D.set static route 0/0 next-hop 43.18.7.1 qualified-next-hop 76.13.10.2 preference 10
Answer: D
Juniper JN0-360 JN0-360 examen
NO.8 Which Junos operational mode command is used to verify that load balancing is working as expected?
A.show route all
B.show route extensive
C.show route balancing
D.show route forwarding-table
Answer: D
Juniper JN0-360 certification JN0-360
NO.9 Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a stub
area Which two LSA types does Router A suppress from Area 1 ?
A.Router LSA
B.External LSA
C.Summary LSA
D.ASBR Summary LSA
Answer: B D
certification Juniper JN0-360 JN0-360 examen
NO.10 You have been asked to configure an IPv6 address for a group of interfaces that could belong on
different routers. If a packet is sent to that address, it should be received by all routers in the group.
Which address type would be suited for these requirements?
A.Unicast
B.Multicast
C.Anycast
D.Broadcast
Answer: B
Juniper JN0-360 examen certification JN0-360 certification JN0-360 JN0-360
NO.11 You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs) from
area 0 (other than the default route) You have configured your area to be stub, but you still see type 3
LSAs.
What will account for this behavior?
A.You should have configured your area as totally stubby
B.You should have used a not-so-stubby-area
C.You are experiencing a routing loop
D.You have exported routes into OSPF
Answer: A
Juniper JN0-360 JN0-360 examen
NO.12 Click the Exhibit button
Based on the illustration of the VPLS topology shown in the exhibit, which statement is true?
A.PE-C must have a spanning-tree protocol enabled
B.CE-C must have BGP enabled
C.Traffic forwarded from PE-C to PE-A is forwarded on to PE-B
D.Traffic forwarded from PE-C to PE-A is not forwarded on to PE-B
Answer: D
Juniper examen certification JN0-360 JN0-360 examen JN0-360 examen JN0-360
NO.13 Which role does the router ID (RID) have in the BGP route selection process?
A.The router ID is evaluated immediately after MED to determine route preference
B.The router ID is evaluated last in the route selection process
C.The router ID is evaluated after the cluster length and a lower router ID is chosen
D.The router ID is evaluated after analyzing the IGP metric cost
Answer: C
Juniper certification JN0-360 JN0-360
NO.14 You have configured an IP-IP tunnel between Router A and Router B
Which Junos operational mode command is used to verify that the tunnel interface is up and operational?
A.show chassis tunnel status
B.show tunnel interface
C.show interfaces terse
D.show interfaces tunnel
Answer: C
Juniper examen JN0-360 JN0-360 examen JN0-360
NO.15 You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy. You
have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and 10.10.10.5
as its secondary next-hop.
Which command correctly configures this scenario?
A.set static route 8/8 10.10.10.1 qualified-next-hop 10.10.10.5 pref 10
B.set static route 8/8 next-hop 10.10.10.1 secondary-next-hop 10.10.10.5 preference 10
C.set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10
D.set static route 8/8 next-hop [10.10.10.1 10.10.10.5] pref 10
Answer: C
Juniper examen JN0-360 examen JN0-360 JN0-360 JN0-360 examen
NO.16 Click the Exhibit button
You work for the regional Internet service provider shown in the exhibit You have a partial BGP table and
are receiving a 10 100/16 route from your upstream ISP You have been asked to configure a default route
that can be sent to your downstream customer This route should forward customer traffic toward your
upstream Tier 11SP as long as the 10.100/16 route is present.
What would accomplish this goal?
A.Create and announce an aggregate default route
B.Create and announce a static default route with a next-hop of discard
C.Create and announce a static default route with a next-hop of reject
D.Create and announce a generated default route
E.Create an advertise-map with exist-map
Answer: E
Juniper JN0-360 examen JN0-360 certification JN0-360
NO.17 Which two values displayed in the output from the show spanning-tree MSTP configuration command
must match on all switches participating in the same MSTP region? (Choose two)
A.root bridge identifier
B.authentication checksum
C.context identifier
D.configuration digest
Answer: CD
certification Juniper JN0-360 certification JN0-360 JN0-360 examen JN0-360
NO.18 Click the Exhibit button
In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals
Which router will be the designated router?.
A.R1
B.R2
C.R3
D.R4
Answer: A
Juniper examen JN0-360 examen JN0-360 JN0-360
NO.19 Click the Exhibit button
Referring to the network illustrated in the exhibit, how does router A reach destinations in area 49.2222?
A.Router A will use the routes from area 49.2222; it learns from router B
B.Router A will see the attached bit from router B and create a default route
C.Router A must have a default route manually configured
D.Router A will receive a default route in the IS-IS update from router B
Answer: B
Juniper examen JN0-360 JN0-360 certification JN0-360
NO.20 Which two statements describe differences between IPv4 and IPv6.? (Choose two)
A.IPsec is built into IPv6
B.IPv6 uses a 32-bit (4-byte) address and can support up to 4,294,967,296 addresses
C.IPv4 supports extension headers whereas IPv6 options are integrated into the base
D.IPv6 eliminates the need for NAT
Answer: AD
Juniper certification JN0-360 JN0-360 examen JN0-360 JN0-360 certification JN0-360
Certification Juniper JN0-360 est un des tests plus importants dans le système de Certification Juniper. Les experts de Pass4Test profitent leurs expériences et connaissances professionnelles à rechercher les guides d'étude à aider les candidats du test Juniper JN0-360 à réussir le test. Les Q&As offertes par Pass4Test vous assurent 100% à passer le test. D'ailleurs, la mise à jour pendant un an est gratuite.
没有评论:
发表评论